How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
The content down below relating to Tools You Need to Install a New Bathtub is unquestionably insightful. Read on and draw your own assumptions.
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you have to open a wall to eliminate the old bathtub and place the brand-new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the new one. Make certain you have certified on your own for the job and are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Possibilities are you might require a specialist plumber to make tube connections.
This article will help you install a new bathtub in your restroom if you have already purchased a new tub and don't need to alter the setup of your previous water supply pipes.
Your devices and also product checklist ought to make up the following:
Getting ready for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is separate the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using both wood boards under its feet, put the bathtub in the called for setting. The wood boards are practical in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub up until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub and likewise check the overflow outlet and also the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been utilized at the very least once as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type ought to be connected to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to break a rigid seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to constantly load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the market. It is a good idea to fit the ceramic tiles using waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very intrigued by How to Install a Bathtub Yourself and I really hope you appreciated my page. For those who liked our blog entry please remember to pass it around. Thanks a bunch for your time. Visit again soon.
Schedule Your Job Now Report this page